Rear wheel won't spin freely when I tighten the axle nut.

Use a pointer against the rim as you spin the wheel this time. Loosen one side where it pushes against the pointer and tighten the other, a little, to move the rim side to side. Check offset and make adjustments if necessary. Repeat 4, 5 and 6 until within acceptable limits, don't expect perfection. Sorry for the late update, but the problem is solved now. I checked on the bike after a month to find that the front brakes were dragging now too, even more than the front (even hard to rotate by hand). Took Riceburner's suggestion and everything seemed to clear up after one ride. Wheels both spin freely when on the centre stand now.

Rear wheel hard to spin? | Honda Motorcycles - FireB.

Whether you’re a die-hard motocross enthusiast or adventurous bike rider who has the passion for everything motorcycle, you definitely enjoy riding your bike and feeling the wind in the face. As with any other vehicle, wheels are an integral part of your bike and without them you wouldn’t be able to move it anywhere unless you’re a wizard.

Rear wheel is hard to spin. Brakes maybe? - WR400F/426F/450F - ThumperTalk.

Rear sag is the measure of change in rear ride height when comparing a fully extended suspension to a loaded suspension. Typically loaded and unloaded sag are considered (sometimes called "laden" and "unladen" sag). The reference measurement is the fully-extended suspension (as with the motorcycle wheel off the ground). First thing that happens... the plastic chain guard on the rear sprockets that keeps the chain from going into the spokes breaks. It gets lopsided and starts rubbing so I cut it out of there. Now the rear wheel does not spin freely. If I pick the rear wheel off the ground and spin it in the forward direction the pedals sort of tick forward. 13,079 Posts. #5 · Jun 7, 2009. The front wobbling side-to-side is usually the result of the wheel being off-center or loose. If the spacers were in wrong, I would think that both front calipers/pads would drag. Check the free movement of the wheel without calipers mounted. Then mount one at a time.

Does making the rear wheel on a motorcycle spin while not... - Quora.

Answer (1 of 10): Overheating the engine comes to mind. Airflow is important to an engine, especially if it's revving high during a brakestand or burnout. Motors can overheat during burnouts, if the temp is high when shut off coolant hoses can blow out since coolant stops circulating and temps sp. 2008 R1200GS - rear wheel spin. Just greased driveshaft splines and serviced the bike recently. Have noticed the last 4 gas fillups that my mileage has slipped from 45 mpg to around 41mpg. Driveshaft is fine and I can spin the rear wheel (when on the center stand) 1 full turn freely. Modified 4 years, 9 months ago. Viewed 277 times. 2. With my bike on a paddok stand and turned on, I know the rear wheel spins in neutral but when I put it in gear and pull the clutch lever in it still continues to spin. Now the question is I can stop the wheel with my hand or foot but the wheel feels like it wants to pull, this is still in.

How free should the rear wheel be spinning? - reddit.

If you can feel looseness, the wheel bearings need further inspection. When the wheel is off, push a finger in the hole where the axle goes and try to turn the bearing. If the bearing sticks as. The dolly is made of heavy-duty laser-cut plate steel to ensure superior strength. There’s also an adjustable kickstand arm to fit most bikes where the center of the rear wheel to kickstand measures 34 – 50 inches. Pros. Can accommodate many types of motorcycles ; Made of high-quality materials; Comes with wheel locks for safety; Bike is.

Rear wheel hard to spin, bike engaged in neutral.

Joined Sep 17, 2008. 607 Posts. #2 · Aug 3, 2013. ArmyRider said: Adjusted my chain, and my rear wheel is kinda hard to spin. It'll make about a full rotation with a good spin. I am new to the whole chain adjustment, but all I did was loosen the big nut on the back, and it is a 2007 GSXR600, so it has lock bars on the swingarm, to align the tire. Pull the wheels, pull the drums, put a wheel back on and try again, see how much it changes. Unbolt the rear of the driveshaft. Once you're down to just the rearend without drums or driveshaft it should turn very freely. JEM, Aug 14, 2013. SHARE POST #8. Even with the clutch disengaged (clutch lever pulled in) the plates still slip past eachother and rub together slightly and that slight rubbing is enough to spin the rear wheel. If it is spinning the rear wheel with more than hand pressure required to stop the rear wheel then you might have a clutch dragging problem.

Question - Why rear wheels hard to spin ? | The H.A.M.B.

153. 307. The spacer is there to prevent side load on the bearing. If you cut it,the axle spacers will push the center of the bearing in, causing it to fail even sooner. We posted at the same time. I see you found the reason. Last edited: Aug 25, 2011. Breeze3at, Aug 25, 2011. #2.

Rear wheel wont freely spin - ProBoards.

Check The Alignment Of The Rear Wheel. Now it's time to check the read wheel. Brian MacLean. With the front wheel aligned, once again bring the rope to the leading edge of the rear tire. Draw.

Other content:

Spin The Bottle Challenge

Top 15 Casinos Nz

Poker Hud Free Trial

Draft Guard Mail Slot

Motorcycle rear wheel hard to spin